Mark W. Jarzomski, PE, MBA
2206 Potomac Drive Unit B
Houston, Texas 77057
mark@jarzomski.com

Experience:
Solar Turbines Inc., Houston, Texas
1/2005 to present, Senior Project Engineer

• Project Engineer for a 400-mmscfd Natural Gas compressor station in Waller, Texas. Compressor station included one Solar Centaur 40 compressor set complete with slug catcher, inlet filter/separator, MCC building, standby diesel generator, BOP piping and controls.
  
• Lead Mechanical Design Engineer for five (5) Single Lift Modules for Pemex KU-A2.
  

• Solutions developed for centrifugal compressor packages for process gas compression requirements worldwide. Responsible for equipment selection, project scope definition, compressor performance, comments to customer specifications.

• Lead proposal engineer for development of a 1100MW combined cycle plant in North Carolina. Preparation of equipment specifications, equipment list. Coordination of proposal development including process flow diagrams, P&ID's, general arrangement drawings, and statement of work.
• Construction assistance for engineered pipe supports at a new 820MW power generation facility in Sterlington, Louisiana. Site consists of 3 power blocks, each based on GE 7FA combustion gas turbines, Aalborg HRSGs and GE steam turbines.
• Creation of landfill gas compression and treatment specifications for a proposed 25MW Waste to Energy Power Generation facility outside of Seattle, Washington.
• Preparation of proposal statement of work, development of specifications for HRSGs, boiler feedwater pumps, tail gas compressors for a proposed 235MW Combined Heat and Power Facility in Sao Paulo Brazil. Combustion Gas Turbines include two (2) Siemens-Westinghouse 501D5A's.

• Preparation of specifications for mechanical equipment, and completion of technical bid evaluations of vendor bids required for installation of gas turbines for use in power generation and gas transmission applications.
• Preparation of Process Flow Diagrams, and P&ID's to define project scope of supply. Mechanical design of fuel gas, steam, and other piping systems as required to ASME B31.1, B31.3, and B31.8 piping codes.
• Review vendor approval drawings and documentation for accuracy and compliance with project specifications.
• Development of project specifications for Heat Recovery Steam Generators; boiler feedwater pumps; fuel gas filter/separators; and selection of mechanical equipment for a 19 MW cogeneration facility in Belle Chase, Louisiana.
• Start-Up assistance of cogeneration facilities in Lawrence, Massachusetts and Wallingford, Connecticut. Primary responsibility for fuel gas compressor start-up while assisting Solar Field Service representatives and plant operators commission turbine generator sets and balance of plant equipment.
• Inlet slug catchers; compressor suction scrubbers; air cooled heat exchangers; manual valves selected for re-staging of a 225 mmscfd natural gas transmission station located on an offshore platform in Azerbaijan.
• Specification of Compressor Suction Scrubbers; fuel gas treatment skids; and the balance of plant mechanical equipment for a 130 mmscfd expansion to the Williams Kern River natural gas pipeline. New Installation of Compressor stations at Daggett California , Veyo Utah , and Elberta Utah.
• Specification of controls, instrumentation, and mechanical equipment for a Solar Taurus 70 installation in New York State. Coordination of fuel gas compressor start-up and commissioning with client and compressor manufacturer.
• Fuel gas compressor specification, selection, start-up, and trouble-shooting for Solar Turbines domestically and abroad.

• Solutions developed for API 618 reciprocating compressor packages for customer refinery and process gas compression requirements worldwide. Responsible for equipment selection, project scope definition, compressor performance, comments to customer specifications.

• Approval of project Piping and Instrument diagrams and General Arrangement drawings. Creation of specifications and datasheets to source ASME section VIII pressure vessels, heat exchangers, pumps, motors, valving, and instrumentation.
• Coordination of engineering activities from project quotation through the warranty period to manufacture and procure components for an ISO 9001 certified facility.

Additional Information:
Computer Experience- GateCycle, CAESAR II pipe stress analysis, HySIM / HySYS Process Simulation, MS Excel, PowerPoint, and Word. Programming languages include Fortran, and C.
Honors- Phi Kappa Phi Honor Society, Sigma Tau Iota Honor Society, Texas Alpha Chapter of Beta Gamma Sigma
Professional Memberships- A.S.M.E., National Society of Professional Engineers
License- Texas Professional Engineer # 98281 (Mechanical)